Breather Valve TA294-R
SKU: TA294-R

Breather Valve TA294-R

Description

The TA294-R Breather Valve was designed to meet the need for a low cost, two-way valve for use on transit cases and similar applications up to 8 cubic feet in volume. It is similar to TA292-R Breather Valves, except it is longer and has a flow rate of 1.0 SCFM at a pressure of 1.5 psi to 2.0 psi above the valve setting. Standard settings range from 0.5 psid to 3.0 psid reseal pressure.

The valve is tamper-proof and requires no field maintenance. Corrosion-resistant materials are used throughout. The valve seal is made of silicone rubber. Each valve comes complete with a nut, washer and gasket. A manual release push button is standard on all TA294-R valves. It is used to equalize pressure or vacuum differentials in order to open the container.

Materials Housing, Hex Nut & Washer - Aluminum Alloy, Gasket - AMS-R-6855, Class II, Grade 60
Finish Alodine with anodized hex nut
Mounting Requirements Gasket, washer & hex nut, provided with each valve
Mounting Hole Diameter 0.78 ± 0.015 (20 ± 0.4 mm)
Maximum Wall Thickness 0.10 (3 mm)
Installation Torque 25-35 in. - lbs. (3.0-4.0 N•m)
Weight 0.02 lbs. (32 grams)

For threaded boss installation: 0.750-16 UNF-2B; no counterbore requirement
Contact AGM's Engineering department for information on NEMA and IP ratings.

TA294-R Breather Valve drawing

PRESSURE SIDE (FLOW OUT)
VACUUM SIDE (FLOW IN)
Dash No.
Sealed @
Flow Rate
Dash No.
Sealed @
Flow Rate
-05
0.5 psid*
1.0 SCFM† @ 2.0 psid*
-05
0.5 psid*
1.0 SCFM† @ 2.0 psid*
-10
1.0 psid*
1.0 SCFM† @ 2.5 psid*
-10
1.0 psid*
1.0 SCFM† @ 2.5 psid*
-15
1.5 psid*
1.0 SCFM† @ 3.0 psid*
-15
1.5 psid*
1.0 SCFM† @ 3.0 psid*
-20
2.0 psid*
1.0 SCFM† @ 3.5 psid*
-20
2.0 psid*
1.0 SCFM† @ 3.5 psid*
-25
2.5 psid*
1.0 SCFM† @ 4.5 psid*
-25
2.5 psid*
1.0 SCFM† @ 4.5 psid*
-30
3.0 psid*
1.0 SCFM† @ 5.0 psid*
-30
3.0 psid*
1.0 SCFM† @ 5.0 psid*

*To convert to metric equivalent (millibars) multiply by 69
†To convert metric equivalent (liters/sec) multiply by 0.472
Dash numbers for the Pressure and Vacuum sides may be used in any combination (i.e. TA294-05-15-R). Before making drawings of these valves, contact AGM for part numbers to be used.

Additional Information

Materials

Housing & Hex Nut-Aluminum Alloy, Gasket-AMS-R-6855, Class II, Grade 50

Finish

Alodine with anodized hex nut

Mounting Requirements

Gasket, Washer, Hex Nut are provided with each valve

Mounting Hole Diameter

0.78 ± 0.015 (20 ± 0.4 mm)

Maximum Wall Thickness

0.10 in. (3 mm)

Installation Torque

25-35 in. – lbs. (3.0-4.0 N-m)

Weight

0.02 lbs. (8.4 grams)

Tech Sheets