Breather Valve TA292-R

TA292-R Two-Way Pressure & Vacuum Relief Breather ValveThe TA292-R Breather Valve was designed to meet the need for a low cost, two-way valve for use on transit cases and similar applications up to 4 cubic feet in volume.  The valve has separate and distinct settings for both pressure and vacuum relief.  It has a flow rate of 0.5 scfm at a pressure of 1.5 psi to 2.0 psi above the valve setting.  Standard settings range from 0.5 psid to 3.0 psid reseal pressure.

The TA292-R Breather Valve is tamper-proof and requires no field maintenance.  Corrosion-resistant materials are used throughout.  The valve seal is made of silicone rubber.  Each valve comes complete with a nut and o-ring, and is intended for small cases that require a low profile valve.  A manual release push button is standard on all TA292-R valves.  It is used to equalize pressure or vacuum differentials in order to open the container.

Materials and Finish: Housing and hex nut are aluminum alloys.  Standard finish is black anodize.  O-ring is per MS28775-018.  Torque value for installation: 25 in. - lbs. (3.0 N•m)  Weight: 0.02 lbs. (8.4 grams)

Mounting Requirements: Each valve comes complete with a nut and an o-ring.
Mounting hole diameter: 0.76 ± 0.010 (19.3 ± 0.2 mm)
Installation torque: 25-35 in. - lbs. (3.0-4.0 N•m)
Maximum wall thickness: 0.24 (6 mm)
Add washer for wall thickness less than: 0.05 (1.3 mm). (AGM P/N 196284, order separately.)
For threaded boss installation: 0.750-16 UNF-3B; no counterbore requirement.

Contact AGM's Engineering department for information on NEMA and IP ratings.

PRESSURE SIDE (FLOW OUT)

VACUUM SIDE (FLOW IN)

Dash No.

Sealed @

Flow Rate @ Pressure

Dash No.

Sealed @
Flow Rate @ Pressure
TA292-R
TA292-R
-05
0.5 psid*
0.5 scfm† @ 2.0 psid*
-05
0.5 psid*
0.5 scfm† @ 2.0 psid*
-10
1.0 psid*
0.5 scfm† @ 2.5 psid*
-10
1.0 psid*
0.5 scfm† @ 2.5 psid*
-15
1.5 psid*
0.5 scfm† @ 3.0 psid*
-15
1.5 psid*
0.5 scfm† @ 3.0 psid*
-20
2.0 psid*
0.5 scfm† @ 3.5 psid*
-20
2.0 psid*
0.5 scfm† @ 3.5 psid*
-25
2.5 psid*
0.5 scfm† @ 4.5 psid*
-25
2.5 psid*
0.5 scfm† @ 4.5 psid*
-30
3.0 psid*
0.5 scfm† @ 5.0 psid*
-30
3.0 psid*
0.5 scfm† @ 5.0 psid*
*To convert to metric equivalent (millibars) multiply by 69
†To convert metric equivalent (liters/sec) multiply by 0.472
Dash numbers for the Pressure and Vacuum sides may be used in any combination (i.e. TA292-05-15-R). Before making drawings of these valves, contact AGM for part numbers to be used.